If you buy after clicking affiliate links on this site we might receive a commission from companies such as eBay, Amazon etc This does not affect the price you pay.
If you buy after clicking affiliate links on this site we might receive a commission from companies such as eBay, Amazon etc This does not affect the price you pay.
Click here to see similar items on eBay, and to buy.
RENAULT TRANSAXLE FOR MID ENGINED CARS or VW CONVERSION IN VANS. This has been fully rebuilt 5 speed version 3;44 diff and bell housing fitted so it will mate to the special adaptor plates to fit to a to your Conversion kits for V8 Ford or Chevy two available. We also do the special drive shaft adaptors to convert output shafts to standard 100mm CV joints. ~picture one is a Five speed with correct bell housing to work with our conversion kit adaptor plates for V8. Pic 2 the lower gearbox is the 4 speed with the 5 speed above for comparison. Pic 3 shows V6 on the left 4 speed on the right. Pic 4 is again 4 speed lower 5 speed above. pic 5 Four speed with gear shaft mod at rear and a front plate closing housing used on some adaptor conversions to other engines.
I have Small block ford V8 to Renault UN1 adaptor plate and Small block Chevy version plate also available. The rear gear change selector has also been modified for either cable or rod gear shift to operate on it. The gearbox is ready to use. Can supply special output drive shaft adaptors if required, these convert the Renault gearbox output spline shaft to a standard 100 mm CV Joint 6 bolt fitment. Photo’s available on request. If you require the whole conversion flywheel, adaptor plate and Clutch including bearing for a Small block Ford fitment please ask. Likewise for the Ford Modular 4.6 SOHC or DOHC conversion.TWO ONLY. I have been asked what is the buy it now price..The reserve is the start price is this gives the clue. Make no mistake these are full rebuilt, modified for use on V8 engines up to 400hp and have been fitted with the gear shaft mod and correct bell housing ready to use. We have sold over 400 of these over the last 25 years but they are now rare as rocking horse stuff. I have very limited stock and it will not be around for long. Comes with working guarantee and rebuilt by the best guy in the country. And at this price still cheaper than Renault sold them ten years ago! Without the mods. see our other adverts for the adaptor plate, special flywheel and clutch to convert to use renault un1 gearbox for mid engined cars. We can supply hi torque special starter motors also.Collection from Devon only if collecting, last two. We can of course send via courier on pallet both in the UK and overseas. Price on Postcode.
We can also supply the adaptor plate, flywheel and clutch conversion to fit a FORD V8 small block, or FORD Modular SOHC or DOHC 4.6 or 5.0 Engine to the Renault transaxle to be used in a mid engine vehicle kit or project. See our other adverts for the following: Ford Modular V8 4.6 DOHC and SOHC engines. New. Packages can include ready to run engines with all ancillaries. Also available:ECU and wiring harness modified to fit this engine into a project car with minimal wiring for the customer to do, plus plugs and terminals and a cd rom with full instructions and complete back up from our technical department is supplied with this package.WE CAN SUPPLY ALSO Ford Mustang 4.6 SOHC engine new and complete as to use in project or kit cars. Included is the engine and all ancillaries such as air con pump, Steering pump, exhaust headers, intake manifold and Throttle body, Alternator, serpentine belt. Engine wiring. Extras if required as follows / Extra costs: clutch uprated 450Included is the complete engine management system with ECU to run this engine in ANY project car. 1500 cost.
NEW. Suitable for most V8 projects such as GT40 LAMBORGHINI type build- so many other mid engined projects. This engine is Used in Many cars such as mustang, MG 260, AC cars, and other production cars alike. Price for cash on collection unless you wish it to be shipped via courier then pay pal or bank transfer. Can possibly deliver for arranged costs.I have around 5 pictures of this engine adaptor plate and gearbox, if you wanted a particular shot please contact me. I have more pictures if you send email address. Please see my other advert for Ford Mustang DOHC 4.6 engine new.Located near Honiton and Exeter Devon. Can deliver for costs to be agreed in advance. Can be shipping in the UK via courier. Costs vary due to distances but average is 20 pounds to UK T. It may though be less expensive than collect costs.Hot off the press news. We now offer a stand alone Engine management system for this motor so It can be used in any project cars. This will be a ready to operate system with ECU, connectors, wiring made to suit the Ford Engine all terminated. Just add power, earth, fuel pump relay and starter button. A base running map will be included and you can either have upgrade maps from us for your vehicle or run on a rolling road for best results. The Price is for this specially made system for 1500. This eliminates the need for the Ford Mustang body chassis wiring harness and standard ECU. This new system will also allow mapping and full engine tuning with rolling road. Payment is either bank transfer or Cash on collection OR PAY PAL WITH FEES. We can and have shipped these engines overseas. The goods will need to be transported by Freight carrier and the costs vary depending on the postcode and country of destination. contact us for a quote. international buyers are welcome to either collect or use their own freight carrier.Last two now. These gearboxes are extremely rare and to find.
If you buy after clicking affiliate links on this site we might receive a commission from companies such as eBay, Amazon etc This does not affect the price you pay.
Click here to buy, and to see similar items on eBay
Category: Vehicle Parts and Accessories:Car Parts:Other Car Parts
Location: Honiton